VESA Digital Flat Panel

DFP
TypeDigital video connector
Production history
DesignerVideo Electronics Standards Association
DesignedFebruary 14, 1999
SupersededVGA connector
Superseded byDigital Visual Interface
General specifications
Pins20
Data
Data signalPanelLink protocol Transition Minimized Differential Signaling
Width3 bits plus clock
Max. devices1
ProtocolPanelLink (Serial)
Pinout
Pin 1TMDS data 1 +
Pin 2TMDS data 1 –
Pin 3GND
Pin 4GND
Pin 5TMDS data C +
Pin 6TMDS data C –
Pin 7GND
Pin 8+ 5V
Pin 9Reserved
Pin 10Reserved
Pin 11TMDS data 2 +
Pin 12TMDS data 2 –
Pin 13GND
Pin 14GND
Pin 15TMDS data 0 +
Pin 16TMDS data 0 –
Pin 17Reserved
Pin 18Reserved
Pin 19DDC data
Pin 20DDC clock

The VESA Digital Flat Panel (DFP) interface standard specifies a video connector and digital TMDS signaling for flat-panel displays.[1] It features 20 pins and uses the PanelLink protocol; the standard is based on the preceding VESA Plug and Display (P&D) standard, ratified in 1997. Unlike the later, electrically-compatible Digital Visual Interface (DVI, 1999), DFP never achieved widespread implementation.

History

P&D combined analog and digital video with data over USB and FireWire to reduce cable clutter, but the feature creep resulted in an unpopular, expensive connector.[2]: 4  Compaq described DFP as a "transition" step between the analog VGA connector and P&D: DFP was designed by a consortium including Compaq, Hewlett-Packard, and ATI Technologies as a smaller, simpler connector, dropping support for analog video and data in favor of transmitting exclusively digital video signals.[1]

The connector was used by displays such as the Compaq Presario FP400, FP500, FP700, Fp720, 5204, and 5280. It was offered on graphics cards such as the Xpert LCD,[3] and Rage LT Pro by ATI Technologies, and the Oxygen GVX1[4] by 3Dlabs.

Design

DFP is compatible electrically with P&D (and by extension, DVI); DFP uses the Display Data Channel (DDC) standard level DDC2B for operation and the Extended Display Identification Data (EDID) protocol to identify the display to the host.[5]: §1.2  Like the preceding P&D, DFP uses the PanelLink TMDS protocol developed by Silicon Image for digital video signals.[2]

The DFP standard specifies a 20-pin mini D ribbon connector;[5]: §3.3  however, as the signal protocols are identical, DFP connectors generally are compatible with devices equipped with a DVI interface by using a passive adaptor.

All DFP-compliant devices are required to support resolutions of 640×400, 720×400, and 640×480 (each at a refresh rate of 60Hz) as a minimum level of interoperability, although the resulting display may not necessarily be centered or scaled.[5]: §3.7 

DFP was superseded by DVI because DFP, like P&D, is limited to a single-link TMDS signal. In contrast, DVI is capable of higher maximum resolutions because it supports a dual-link TMDS signal; in addition, DVI also supports analog video, which makes the VGA connector redundant.[2]

References

  1. ^ a b Manchester, Gary (1999). The VESA Digital Flat Panel (DFP) Standard: A White Paper (PDF) (Report). VESA Marketing Committee. Archived from the original (PDF) on January 12, 2016.
  2. ^ a b c Digital Visual Interface & TMDS Extensions (PDF) (Report). Silicon Image. October 2004. Retrieved 31 January 2023.
  3. ^ "XPERT LCD". Archived from the original on 2003-07-21.
  4. ^ "Oxygen GVX1 AGP specs sheet" (PDF).
  5. ^ a b c "VESA Digital Flat Panel (DFP) Standard, Version 1" (PDF). Video Electronics Standards Association. February 14, 1999. Archived from the original (PDF) on June 2, 2001. Retrieved January 31, 2023.
  • DFP diagram and description of pin layout
  • DFP is mentioned in ATI's description of the Xpert LCD


Retrieved from "https://en.wikipedia.org/w/index.php?title=VESA_Digital_Flat_Panel&oldid=1312423521"